Exam NSE7_SDW-7.2 All Questions

View all questions & answers for the NSE7_SDW-7.2 exam

Exam NSE7_SDW-7.2 topic 1 question 1 discussion

Actual exam question from Fortinet's NSE7_SDW-7.2

Question #: 1
Topic #: 1

Refer to the exhibit.

The exhibit shows the BGP configuration on the hub in a hub-and-spoke topology. The administrator wants BGP to advertise prefixes from spokes to other spokes over the IPsec overlays, including additional paths. However, when looking at the spoke routing table, the administrator does not see the prefixes from other spokes and the additional paths.
Based on the exhibit, which three settings must the administrator configure inside each BGP neighbor group so spokes can learn other spokes prefixes and their additional paths? (Choose three.)

A. Enable soft-reconfiguration
B. Enable route-reflector-client
C. Set additional-path to send
D. Set adv-additional-path to the number of additional paths to advertise
E. Set advertisement-interval to the number of additional paths to advertise

Show Suggested Answer

Suggested Answer: BCD 🗳️

by IBB90704 at March 8, 2024, 12:48 a.m.

Comments

Submit Cancel

romartinedg

Highly Voted 1 year ago

B: enable route-reflector-client | Guia 7.2 pag. 240 C: additional-path to send | Guia 7.2 pag. 254 D: adv-additional-path | Guia 7.2 pag. 254

upvoted 5 times

...

Xartr

Most Recent 1 month, 1 week ago

Selected Answer: BCD

Hello, has anyone taken this exam recently? are these questions still valid?

upvoted 2 times

...

Slikings

4 months, 4 weeks ago

Selected Answer: BCD

A: is wrong because soft reconfiguration was not mentioned in the 7.2 SG. The only mention of it was in the context of soft clear. Soft reconfiguration is a method in which fortigate stores BGP routing information using hardware resources. B: Is correct because by default IBGP does not pass on learned routes between spokes, it can however when you enable the route reflector command. When this is enabled on the neighbor group it will forward routes of its peers to other spokes from the hub. C: is correct, this is because this setting enables the ability to identify 2 additional paths and select them. D: is correct, this is because the neighbor groups need to be assigned how many paths they can send on that neighbor. E: is incorrect, this is because the advertisement interval is used in regards to route failover. It is used to speed up convergence by lowering the time that it Fortigate waits between BGP updates by reducing the advertisement interval for dead peers.

upvoted 1 times

...

mitkotest

1 year, 2 months ago

B & C & D are correct

upvoted 1 times

...

nse_student

1 year, 2 months ago

Selected Answer: BCD

BCD are correct!

upvoted 1 times

...

TTOG

1 year, 2 months ago

I wanted to share with you my experience (sadly the exam comment section is removed) : I passed the exam a couple of days ago. There were 40 questions 5-6 of them not from here. A friend of mine failed it, most of his questions were not from here, some of them were from 7.0 he found out later.

upvoted 4 times

ipv84

1 year, 2 months ago

Hi TTOG, so if I understand correctly what you have said, the questions for the 7.2 exam is a mix of questions between these and those of 7.0 ?

upvoted 1 times

J_Olin

1 year, 1 month ago

That is very typical in Fortinet exams. They aren't going to rewrite a whole new test when really only about 5% of the content changed (the part related to new features). Always study at least the current exam version and the one previous.

upvoted 3 times

...

alejandrofern43

1 year, 3 months ago

Selected Answer: BCD

Enable route-reflector-client (pag 239 Sd WAN Study guide for fortios-72) set additional-path to send (pag 252/290 Sd WAN Study guide for fortios-72) set adv-additional-path to the number of addional paths to advertise (pag 290 Sd WAN Study guide for fortios-72)

upvoted 3 times

...