exam questions

Exam NSE7_SDW-7.0 All Questions

View all questions & answers for the NSE7_SDW-7.0 exam

Exam NSE7_SDW-7.0 topic 1 question 32 discussion

Actual exam question from Fortinet's NSE7_SDW-7.0
Question #: 32
Topic #: 1
[All NSE7_SDW-7.0 Questions]

Refer to the exhibit.

The exhibit shows the SD-WAN rule status and configuration.
Based on the exhibit, which change in the measured latency will make T_MPLS_0 the new preferred member?

  • A. When T_INET_0_0 and T_MPLS_0 have the same latency.
  • B. When T_MPLS_0 has a latency of 100 ms.
  • C. When T_INET_0_0 has a latency of 250 ms.
  • D. When T_N1PLS_0 has a latency of 80 ms.
Show Suggested Answer Hide Answer
Suggested Answer: D 🗳️

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
henryx
5 months, 2 weeks ago
Selected Answer: D
D is correct. PoBratsky clarifies this.
upvoted 1 times
...
Moad
7 months, 3 weeks ago
B. When T_MPLS_0 has a latency of 100 ms.
upvoted 1 times
...
PoBratsky
9 months, 3 weeks ago
Selected Answer: D
D is correct.
upvoted 1 times
...
PoBratsky
9 months, 3 weeks ago
D is correct. I think T_N1PLS_0 is T_MPLS_0 real metric / (1 + link cost threshold / 100) = CM (Correct metric) 101.349 / (1 + 10 / 100) = CM 101.349 / 1.1 = 92.13545454545455 T_MPLS_0 - 80ms < T_INET_0_0 - 92 Preferred member is T_MPLS_0
upvoted 3 times
...
IETF1
10 months ago
B. When T_MPLS_0 has a latency of 100 ms.
upvoted 1 times
...
charruco
11 months, 4 weeks ago
B is correct T_N1PLS_0 does not exist
upvoted 2 times
...
TheUsD
12 months ago
Selected Answer: B
Not sure why people are posting "D" as the answer. It is not an interface showing on the exhibits. Because of this, "B" "When T_MPLS_0 has a latency of 100 ms." should be the correct answer. Did someone make a major typo?
upvoted 3 times
Comatose
9 months ago
Cause when they posted the answers, they typo'd. There's a break down of the actual math in one of the other answers.
upvoted 1 times
...
...
TheUsD
12 months ago
Not sure why people are posting "D" as the answer. It is not an interface showing on the exhibits. Because of this, "B" "When T_MPLS_0 has a latency of 100 ms." should be the correct answer. Did someone make a major typo?
upvoted 1 times
...
shinichi18
1 year ago
Selected Answer: B
T_N1PLS_0? where?
upvoted 3 times
...
themageofsec
1 year, 3 months ago
Selected Answer: D
D is correct Study Guide 7.0, page 174 Study Guide 7.2, page 200
upvoted 2 times
...
Tcmh
1 year, 3 months ago
Selected Answer: D
D Link-cost-threadhold =10 so actual latence of INT_0_0 = 101.349 * 0.9 =91.2141 so Int_MPLS less than 91.2141 to take over, so D is correct
upvoted 1 times
...
Welisson2
1 year, 3 months ago
Selected Answer: D
D is correct
upvoted 1 times
...
draven76
1 year, 4 months ago
Selected Answer: D
Official study guide, page 174. link-cost-treshold is set to 10 (percent) so the other link must have a latency of less than 90% of the preferred link
upvoted 2 times
...
draven76
1 year, 4 months ago
Official study guide, page 174. link-cost-treshold is set to 10 (percent) so the other link must have a latency of less than 90% of the preferred link
upvoted 1 times
...
cstevens97
1 year, 4 months ago
Selected Answer: D
D is the correct answer.
upvoted 1 times
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
Loading ...
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago