ExamTopics Logo
Mail Us[email protected]
Menu
Cisco Discussions
exam questions

Exam 500-220 All Questions

View all questions & answers for the 500-220 exam
Go to Exam

Exam 500-220 topic 3 question 24 discussion

Actual exam question from Cisco's 500-220
Question #: 5
Topic #: 3
[All 500-220 Questions]


Refer to the exhibit. Which two actions are required to optimize load balancing asymmetrically with a 4:1 ratio between links? (Choose two.)

  • A. Change the primary uplink to "none".
  • B. Add an internet traffic preference that defines the load-balancing ratio as 4:1.
  • C. Enable load balancing.
  • D. Set the speed of the cellular uplink to zero.
  • E. Change the assigned speeds of WAN 1 and WAN 2 so that the ratio is 4:1.
Show Suggested Answer Hide Answer
Suggested Answer: CE 🗳️
by alfonsocav1982 at Nov. 3, 2022, 7:44 p.m.

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
Submit Cancel
rnunes1110
5 months, 2 weeks ago
Selected Answer: CE
C and E for sure: The MX can be configured to use both of its uplinks for load balancing. When load balancing is enabled under Security & SD-WAN > Configure > SD-WAN & Traffic shaping, traffic flows will be distributed between the two uplinks. The load distribution is based on the WAN 1 and WAN 2 throughput configured under Uplink configuration, such that the uplink with more throughput will distribute more flows. In the example below, WAN 1 is configured to pass 50Mb/s, and WAN 2 is configured to pass 10Mb/s. Since the download speed ratio is 5/1, for every five flows sent over WAN 1, a single flow will be sent over WAN 2: Refer: https://documentation.meraki.com/MX/Firewall_and_Traffic_Shaping/MX_Load_Balancing_and_Flow_Preferences
upvoted 2 times
...
CaptainPirate
8 months, 2 weeks ago
Add an internet traffic preference that defines the load-balancing ratio as 4:1. -This can be used to control the routing of specific types of traffic, but it will not affect the overall load balancing of the MX.answer CE
upvoted 1 times
...
Jean226
10 months, 3 weeks ago
Selected Answer: CE
Has anyone here taken the exam yet ?
upvoted 4 times
...
18HandsOfLohan
1 year, 2 months ago
Selected Answer: CE
CE is correct as a ratio balancing will be set through configured throughput on WAN 1/2.
upvoted 2 times
...
Netmanb2k
1 year, 5 months ago
C and E The MX can be configured to use both of its uplinks for load balancing. When load balancing is enabled under Security & SD-WAN > Configure > SD-WAN & Traffic shaping, traffic flows will be distributed between the two uplinks. The load distribution is based on the WAN 1 and WAN 2 throughput configured under Uplink configuration, such that the uplink with more throughput will distribute more flows. https://documentation.meraki.com/MX/Firewall_and_Traffic_Shaping/MX_Load_Balancing_and_Flow_Preferences
upvoted 2 times
...
alfonsocav1982
1 year, 5 months ago
Selected Answer: CE
It should be C and E. Changing the assigned speed will automatically load balance preferring the faster link.
upvoted 1 times
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago