exam questions

Exam 300-425 All Questions

View all questions & answers for the 300-425 exam

Exam 300-425 topic 1 question 13 discussion

Actual exam question from Cisco's 300-425
Question #: 13
Topic #: 1
[All 300-425 Questions]

A wireless engineer is performing a post verification of a wireless network. Which two metrics does the engineer verify to ensure that the wireless network can support voice services? (Choose two.)

  • A. The coverage area must have a noise floor that does not exceed גˆ’87 dBm.
  • B. The client device must have at least an גˆ’67 dBm RSSI.
  • C. The rate of retransmitted packets must be 15 percent or below.
  • D. The rate of retransmitted packets must be 20 percent or below.
  • E. The client device must have at least an גˆ’65 dBm RSSI.
Show Suggested Answer Hide Answer
Suggested Answer: BD 🗳️

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
skh
Highly Voted 3 years, 11 months ago
B&D should https://www.cisco.com/c/en/us/td/docs/wireless/technology/vowlan/troubleshooting/vowlan_troubleshoot/8_Site_Survey_RF_Design_Valid.html RF Design Validation 1. The optimal VoWLAN Cell Edge recommendation is -67 dBm. 2. An optimal VoWLAN deployment will require at least a 20 percent cell overlap for 2.4 GHz and 15-20 percent for 5 GHz for access points that reside on different channels. 3. Over all Channel Utilization should be less than 50 percent. 4. The Noise floor should not exceed -92 dBm, which facilitates a Signal to Noise Ratio of 25 dB. 5. Retransmissions should be kept under 20 percent. 6. Packet Loss should remain under 1 percent and jitter should be kept to less than 100 ms.
upvoted 15 times
...
ASV2020
Highly Voted 3 years, 6 months ago
Answer: B y D
upvoted 7 times
...
Farhad123
Most Recent 5 months ago
Selected Answer: BD
Retransmissions should be kept under 20 percent. The optimal VoWLAN Cell Edge recommendation is -67 dBm.
upvoted 1 times
...
Farhad123
7 months, 3 weeks ago
B and D
upvoted 1 times
...
ShamsDimashki
9 months, 1 week ago
Selected Answer: BD
B & D are the correct answers
upvoted 1 times
...
JBERTHIER
1 year, 1 month ago
I disagree Answer should A and B A voice design does not accept retransmission
upvoted 1 times
JBERTHIER
1 year, 1 month ago
Sorry my reply is wrong Answer B & D
upvoted 1 times
...
...
ContactScott
1 year, 11 months ago
Selected Answer: BD
RF Design Validation https://www.cisco.com/c/en/us/td/docs/wireless/technology/vowlan/troubleshooting/vowlan_troubleshoot/8_Site_Survey_RF_Design_Valid.html
upvoted 1 times
...
brrrrrrd
2 years, 3 months ago
You should measure using 5 ghz because if that works then 2.4 will for sure work. It could be either or, there isnt enough info here. If the answer says 15% i could see that. I could also see 20% it depends.
upvoted 1 times
...
FabriG
2 years, 3 months ago
Selected Answer: BD
According to Cisco ENWLSD Course, it is B and D.
upvoted 1 times
...
migu0692
2 years, 7 months ago
Selected Answer: BD
B AND D
upvoted 3 times
...
kthekillerc
3 years, 3 months ago
https://www.cisco.com/c/en/us/td/docs/wireless/technology/vowlan/troubleshooting/vowlan_troubleshoot/8_Site_Survey_RF_Design_Valid.html Correct its B and D
upvoted 4 times
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
Loading ...
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago