ExamTopics Logo
Mail Us[email protected]
Menu
Cisco Discussions
exam questions

Exam 350-401 All Questions

View all questions & answers for the 350-401 exam
Go to Exam

Exam 350-401 topic 1 question 107 discussion

Actual exam question from Cisco's 350-401
Question #: 107
Topic #: 1
[All 350-401 Questions]

Refer to the exhibit.

A port channel is configured between SW2 and SW3. SW2 is not running a Cisco operating system. When all physical connections are made, the port channel does not establish.
Based on the configuration excerpt of SW3, what is the cause of the problem?

  • A. The port-channel mode should be set to auto.
  • B. The port channel on SW2 is using an incompatible protocol.
  • C. The port-channel trunk is not allowing the native VLAN.
  • D. The port-channel interface load balance should be set to src-mac.
Show Suggested Answer Hide Answer
Suggested Answer: B 🗳️
by ABC123 at March 22, 2021, 3:30 a.m.

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
Submit Cancel
Reavr
Highly Voted 2 years, 9 months ago
Answer is B. The question states that SW2 is not running Cisco. Therefore it cannot run PaGP (which according to the snippet, SW3 is configured as). So it has to be changed to either channel-group active or passive to do LACP.
upvoted 12 times
...
PedroPicapiedra
Highly Voted 1 year, 9 months ago
Selected Answer: B
The correct is B *** PaGP - Cisco Propietary protocol Config modes: - Desirable - Auto - On *** LACP - Open Standard Protocol Config modes: - Active - Passive - On
upvoted 9 times
...
[Removed]
Most Recent 2 months, 2 weeks ago
Selected Answer: B
B is correct
upvoted 1 times
...
andy_doesnt_like_uucp
4 months, 2 weeks ago
it's a bit silly Q. LAG on the SW2 (not Cisco) wont accept PAGP configuration at all
upvoted 1 times
...
slacker_at_work
6 months, 3 weeks ago
Selected Answer: B
Answer: B Desirable employs the PAgP protocol which is Cisco proprietary and SW2 is not running a Cisco OS.
upvoted 1 times
...
nushadu
1 year, 8 months ago
Selected Answer: B
>SW2 is not running a Cisco operating system. PaGP is Cisco proprietary technology ...
upvoted 2 times
...
Parot
1 year, 10 months ago
Answer is B. Desirable mode means PAGP - cisco proprietary protocol. LACP should be use to setup the link between Cisco and non -Cisco devices.
upvoted 1 times
...
KZM
1 year, 11 months ago
PAGP is Cisco proprietary and LACP is an IEEE 802.3ad open standard protocol. Between Cisco IOS and non-Cisco devices, just support LACP for Link Aggregation. The command "Channel-group xx mode desirable" is used in PAGP. For the LACP configuration, the command should be "Active or Passive" in channel-group mode.
upvoted 1 times
...
Multicast01005e
2 years, 10 months ago
B is absolutely correct
upvoted 3 times
...
kthekillerc
3 years, 2 months ago
B is the correct answer
upvoted 3 times
...
ABC123
3 years, 4 months ago
B is wrong. Answer should be A, as desirable is for Cisco Proprietary PAgP. S1(config)# interface range f0/13 -15 S1(config-if-range)# channel-group 1 mode ? active Enable LACP unconditionally auto Enable PAgP only if a PAgP device is detected desirable Enable PAgP unconditionally on Enable Etherchannel only passive Enable LACP only if a LACP device is detected From: https://packetlife.net/blog/2010/jan/18/etherchannel-considerations/
upvoted 1 times
mustache
3 years, 4 months ago
kindly check the exhibit and read the question carefully before answering! B is correct, wrong Protocol is being used, PAgP is cisco proprietary. LACP is open Standard
upvoted 11 times
...
amgue
3 years, 3 months ago
The question asks for the source of the problem, A gives the solution not the source, the correct answer is B
upvoted 7 times
ArchBishop
2 years, 6 months ago
A is not a solution... Desirable/Auto => PAgP Active/Passive => LACP
upvoted 2 times
...
...
muska04
3 years ago
B is the Correct answer. Auto => PAgP, not supported on non-cisco equipment.
upvoted 4 times
...
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago