ExamTopics Logo
Mail Us[email protected]
Menu
Cisco Discussions
exam questions

Exam 350-401 All Questions

View all questions & answers for the 350-401 exam
Go to Exam

Exam 350-401 topic 1 question 1023 discussion

Actual exam question from Cisco's 350-401
Question #: 1023
Topic #: 1
[All 350-401 Questions]

SIMULATION
-


Guidelines
-

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do no remove any existing configurations from the devices, only those necessary to make the appropriate changes required to fulfill the listed tasks.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question
• When Next is clicked, the lab closes and cannot be reopened.


Topology
-




Tasks
-

The Operations team started configuring several monitoring activities. Complete the configurations for the tasks below.

1. Enable Flexible NetFlow on R1 E0/0 in both directions using the pre-configured flow monitor.
2. Configure the switch port analyzer on Sw1 and mirror all VLAN 12 traffic to interface E1/3 using session number 12.
3. Configure a basic IP SLA ICMP echo operation on R1 to ping PC1 every 300 seconds.


R1
-













Show Suggested Answer Hide Answer
Suggested Answer:
by Priya_Darshi at Oct. 14, 2024, 11:32 a.m.

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
Submit Cancel
f9e40af
Highly Voted 5 months, 2 weeks ago
I had this question, but different requirements 1. Wanted you to add a destination IP address to FlowExporter 2. Wanted a configuration of IP SLA HTTP GET with a server IP address. 3. Monitor session on the SW
upvoted 5 times
...
Libertarian
Most Recent 2 weeks, 4 days ago
R1 int e0/0 ip flow egress ip flow ingress ip flow monitor Q1Flow input ip flow monitor Q1Flow output exit ip sla 10 icmp-echo 10.12.1.2 frequency 300 exit ip sla schedule 10 start-time now life forever end copy running-config startup-config Sw1 monitor session 12 source interface vlan 12 monitor session 12 destination interface e1/3 end copy running-config startup-config
upvoted 1 times
Iarn
1 week, 5 days ago
ip flow egress ip flow ingress Are both old netflow commands and not relevant in this question
upvoted 1 times
...
...
junior34pl
2 months, 1 week ago
Same sim on exam. The only difference was task 1 and 3. Task 1 asked you to add destination ip for the server. 3rd task was asking to configure basic IP SLA HTTP each operation on R1
upvoted 3 times
WENG_POGI
1 month, 2 weeks ago
can please show me the configuration thanks..
upvoted 1 times
...
...
Hoda1185
5 months ago
Hoda1185 0 minutes ago Awaiting moderator approval Hi, i passed the exam 6 Labs (878 without static routes,896 with address family, 1021,1032 sla midified, 1054 same tasks but modified topology,1023 but also modified). and 52 questions.But can someone confirm if it s normal, i passed my exam yesterday in pearson Vue center but until now no feedback from pearson Vue and nothing also received in the center
upvoted 3 times
WENG_POGI
3 months, 1 week ago
can you remember what are those 6 labs?
upvoted 1 times
...
Calinserban
4 months, 3 weeks ago
Sometimes take more time then expected, besides the labs the questions are still available?
upvoted 1 times
...
...
Priya_Darshi
6 months, 2 weeks ago
R1# sh run | sec flow monitor Note: This give you preconfigured flow monitor name, make a note now, go to R1 R1(config)#int e0/0 R1(config-if)#ip flow egress R1(config-if)#ip flow ingress Now, activate flow monitor on interface: R1(config-if)#ip flow monitor Q1Flow input R1(config-if)#ip flow monitor Q1Flow output R1(config-if)#end R1# wr mem SPAN Configuration: SW1(config)# monitor session 12 source interface vlan 12 SW1(config)# monitor session 12 destination interface e1/3 SW1(config)# end SW1# wr Configure IP SLA ISCMP echo on R1: R1(config)#ip sla 10 R1(config-ip-sla)#icmp-echo 10.12.1.2 R1(config-ip-sla-echo)#freqency 300 R1(config-ip-sla-echo)#end R1#wr
upvoted 1 times
Iarn
2 weeks, 6 days ago
You still need to schedule the ip sla to run. ip sla schedule 10 start now life for-ever
upvoted 1 times
...
Farne
4 months, 4 weeks ago
For remote span, what about adding the keywords “encapsulation replicate” to the destination command? (from the OCG) without it the span session would not copy 802.1Q VLAN tags or Layer 2 protocols , like Spanning Tree Protocol (STP) bridge protocol data units (BPDUs), CDP, VTP, DTP, Port Aggregation Protocol (PAgP), or Link Aggregation Control Protocol (LACP). The question mentions “ALL traffic”; correct me if I’m wrong
upvoted 1 times
...
Just_little_me
6 months ago
i would add this to the config R1(config)#ip sla schedule 10 start-time now life forever without it the ip sla doesn't runn
upvoted 2 times
...
Kdom07
6 months, 2 weeks ago
awesome config. the "ip flow egress/ingress" commands are not needed as that is only for traditional netflow, not flexible netflow. --also add the commands to "start" the sla
upvoted 4 times
...
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago