ExamTopics Logo
Mail Us[email protected]
Menu
Cisco Discussions
exam questions

Exam 200-301 All Questions

View all questions & answers for the 200-301 exam
Go to Exam

Exam 200-301 topic 1 question 1258 discussion

Actual exam question from Cisco's 200-301
Question #: 1258
Topic #: 1
[All 200-301 Questions]

SIMULATION
-


Guidelines
-

This is a lab item in which tasks will be performed on virtual devices.

• Refer to the Tasks tab to view the tasks for this lab item.
• Refer to the Topology tab to access the device console(s) and perform the tasks.
• Console access is available for all required devices by clicking the device icon or using the tab(s) above the console window.
• All necessary preconfigurations have been applied.
• Do not change the enable password or hostname for any device.
• Save your configurations to NVRAM before moving to the next item.
• Click Next at the bottom of the screen to submit this lab and move to the next question.
• When Next is clicked, the lab doses and cannot be reopened.


Topology
-




Tasks
-

R1 and R2 are pre-configured with all the necessary commands. All physical cabling is in place and verified. Connectivity for PC1 and PC2 must be established to the switches; each port must only allow one VLAN and be operational.

1. Configure SW-1 with VLAN 15 and label it exactly as OPS
2. Configure SW-2 with VLAN 66 and label it exactly as ENGINEERING
3. Configure the switch port connecting to PC1
4. Configure the switch port connecting to PC2
5. Configure the E0/2 connections on SW-1 and SW-2 for neighbor discovery using the vendor-neutral standard protocol and ensure that E0/0 on both switches uses the Cisco proprietary protocol

Show Suggested Answer Hide Answer
Suggested Answer:
by JunsK1e at Dec. 14, 2023, 12:46 p.m.

Comments

Chosen Answer:
This is a voting comment (?). It is better to Upvote an existing comment if you don't have anything to add.
Switch to a voting comment New
Submit Cancel
Shaifalimittal02
3 months, 2 weeks ago
As far as I have understood the question:- SW-1(config)# vlan 15 SW-1(config-vlan)# name OPS SW-1(config)# interface ethernet 0/1 SW-1(config-if)# switchport mode access SW-1(config-if)# switchport access vlan 15 SW-1(config-if)# no shutdown SW-2(config)# vlan 66 SW-2(config-vlan)# name ENGINEERING SW-2(config)# interface ethernet 0/1 SW-2(config-if)# switchport mode access SW-2(config-if)# switchport access vlan 66 SW-2(config-if)# no shutdown SW-1(config)# interface ethernet 0/2 SW-1(config-if)# lldp transmit SW-1(config-if)# lldp receive SW-1(config-if)# no shutdown SW-1(config)# interface ethernet 0/0 SW-1(config-if)# cdp enable SW-1(config-if)# no shutdown SW-2(config)# interface ethernet 0/2 SW-2(config-if)# lldp transmit SW-2(config-if)# lldp receive SW-2(config-if)# no shutdown SW-2(config)# interface ethernet 0/0 SW-2(config-if)# cdp enable SW-2(config-if)# no shutdown
upvoted 2 times
tollovia
3 days, 20 hours ago
Is this correct or the other one showed above??
upvoted 1 times
...
...
6353e2d
4 months, 1 week ago
How many Simulations should one expect on their test?
upvoted 2 times
exiledwl
3 months, 3 weeks ago
I have seen ppl say 3-4 on reddit
upvoted 1 times
...
...
bymrdas
7 months, 4 weeks ago
----------------SW-1-------------- Task1 vlan 15 name OPS Task3 interface etherne0/1 switchport mode access switchport access lan 15 Task5 lldp run interface ethernet 0/2 lldp transmit lldp receive no cdp enable cdp run interface ethernet 0/0 cdp enable no lldp transmit no lldp receive switchport trunk encapsulation isl switchport mode trunk exit wr -------------SW-2------------------ Task2 vlan 66 name ENGINEERING Task 4 interface etherne0/1 switchport mode access switchport access lan 66 Task5 lldp run interface ethernet 0/2 lldp transmit lldp receive no cdp enable cdp run interface ethernet 0/0 cdp enable no lldp transmit no lldp receive switchport trunk encapsulation isl switchport mode trunk exit wr
upvoted 1 times
bymrdas
6 months, 2 weeks ago
Guys, I know that trunk mode is not necessary, as it is not part of any of the tasks. ----------------SW-1-------------- Task1 vlan 15 name OPS Task3 interface etherne0/1 switchport mode access switchport access lan 15 Task5 lldp run interface ethernet 0/2 lldp transmit lldp receive no cdp enable cdp run interface ethernet 0/0 cdp enable no lldp transmit no lldp receive exit wr -------------SW-2------------------ Task2 vlan 66 name ENGINEERING Task 4 interface etherne0/1 switchport mode access switchport access lan 66 Task5 lldp run interface ethernet 0/2 lldp transmit lldp receive no cdp enable cdp run interface ethernet 0/0 cdp enable no lldp transmit no lldp receive exit wr
upvoted 2 times
...
...
[Removed]
8 months ago
Task 1: Sw1(config)#vl 15 Sw1(config-vlan)#name OPS Task 2: Sw2(config)#vl 66 Sw2(config-vlan)#na ENGINEERING Task 3: Sw1(config)#in fa0/1 Sw1(config-if)#no sh Sw1(config-if)#sw mo acc Sw1(config-if)#sw acc vl 15 Task 4: Sw2(config)#in fa0/1 Sw2(config-if)#no sh Sw2(config-if)#sw mo acc Sw2(config-if)#sw acc vl 66 Task 5 SW1 & SW2: Switch(config)#lldp run Switch(config)#in e0/2 Switch(config-if)#no cdp enable Switch(config-if)#lldp transmit Switch(config-if)#lldp receive Switch(config)#in e0/0 Switch(config-if)#no lldp transmit Switch(config-if)#no lldp receive Switch(config-if)#cdp enable Switch(config-if)#sw tr en isl Switch(config-if)#sw mo tr end copy r st
upvoted 2 times
exiledwl
3 months, 2 weeks ago
I believe when task 5 states use cisco proprietary they are refferring to CDP and not trunking isl
upvoted 1 times
...
...
86a50a6
9 months, 3 weeks ago
shouldn't we use the no cdp enable command on the interfaces towards the routers since cisco is asking to enable LLDP for these interfaces?
upvoted 1 times
...
KuyaErik101
9 months, 3 weeks ago
Correct
upvoted 1 times
...
[Removed]
1 year, 1 month ago
Given answers are correct; no objections. Question is slightly ambiguous as to if CDP has to be disabled on the LLDP interfaces and vice versa. If not, technically just issuing "lldp run" on both switches is sufficient to complete the task, since CPD will be running by default. Better to be safe though.
upvoted 4 times
AbdullahMohammad251
1 year ago
CDP is enabled by default on switches and routers. CDP is enabled globally on all interfaces by default, this means that we don't need to use "cdp enable" command to enable it on the interface. LLDP is disabled by default on all interfaces. LLDP run command enables LLDP but it doesn't we have to manually enable it on each interface using "lldp transmit" and "lldp receive" commands.
upvoted 9 times
...
...
JunsK1e
1 year, 1 month ago
Solution's well explained!
upvoted 2 times
...
Community vote distribution
A (35%)
C (25%)
B (20%)
Other
Most Voted
A voting comment increases the vote count for the chosen answer by one.

Upvoting a comment with a selected answer will also increase the vote count towards that answer by one. So if you see a comment that you already agree with, you can upvote it instead of posting a new comment.

SaveCancel
exam
Someone Bought Contributor Access for:
SY0-701
London, 1 minute ago